11.7. HP JetDirect Interface

 MENU  -> MIO MENU (use MENU to display MIO MENU)
 ITEM  -> CFG NETWORK=NO*
 +     -> CFG NETWORK=YES
 ENTER -> CFG NETWORK=YES*
 ITEM  -> TCP/IP=OFF* (use ITEM to display TCP/IP)
 +     -> TCP/IP=ON
 ENTER -> TCP/IP=ON*
 ITEM  -> CFG TCP/IP=NO* (use ITEM to display TCP/IP)
 +     -> CFG TCP/IP=YES
 ENTER -> CFG TCP/IP=YES*
 ITEM  -> BOOTP=NO*
     (Enable BOOTP if you want to - see below)
 ITEM  -> IP BYTE 1=0*
     This is IP address MSB byte.
     Use +- keys to change value, and then ENTER to change
     Use ITEM keys to get IP BYTE=2,3,4
 ITEM  -> SM BYTE 1=255*
      This is the subnet mask value
     Use +- keys to change value, and then ENTER to change
     Use ITEM keys to get IP BYTE=2,3,4
 ITEM  -> LG BYTE 1=255*
     This is the Syslog server (LoGger) IP address
     Use +- keys to change value, and then ENTER to change
     Use ITEM keys to get IP BYTE=2,3,4
 ITEM  -> GW BYTE 1=255*
     This is the subnet gateway (router) IP address
     Use +- keys to change value, and then ENTER to change
     Use ITEM keys to get IP BYTE=2,3,4
 ITEM  -> TIMEOUT=90
      This is the connection timeout value.  It puts a limit
     on time between connections.  A value of 10 is reasonable.

# Example /etc/bootptab: database for bootp server (/etc/bootpd).
# Blank lines and lines beginning with '#' are ignored.
#
# Legend:
#
#       first field -- hostname
#                       (may be full domain name)
#
#       hd -- home directory
#       bf -- bootfile
#       cs -- cookie servers
#       ds -- domain name servers
#       gw -- gateways
#       ha -- hardware address
#       ht -- hardware type
#       im -- impress servers
#       ip -- host IP address
#       lg -- log servers
#       lp -- LPR servers
#       ns -- IEN-116 name servers
#       rl -- resource location protocol servers
#       sm -- subnet mask
#       tc -- template host (points to similar host entry)
#       to -- time offset (seconds)
#       ts -- time servers
#
# Be careful about including backslashes where they're needed.
# Weird (bad) things can happen when a backslash is omitted
# where one is intended.
#
peripheral1:
:hn:ht=ether:vm=rfc1048:
:ha=08000903212F:
:ip=190.40.101.22:
:sm=255.255.255.0:
:gw=190.40.101.1:
:lg=190.40.101.3:
:T144="hpnp/peripheral1.cfg":

#
# Example HP Network Peripheral Interface configuration file
#
# Comments begin with '#' and end at the end of the line.
# Blank lines are ignored.  Entries cannot span lines.

# Name is the peripheral (or node) name.  It is displayed on the
# peripheral's self-test page or configuration plot, and when sysName
# is obtained through SNMP.  This name can be provided in the BOOTP
# response or can be specified in the NPI configuration file to
# prevent the BOOTP response from overflowing the packet.  The domain
# portion of the name is not necessary because the peripheral does
# not perform Domain Name System (DNS) searches.  Name is limited to
# 64 characters.

name: picasso

# Location describes the physical location of the peripheral.  This
# is the value used by the interface for the MIB-II sysLocation
# object.  The default location is undefined.  Only printable ASCII
# characters are allowed.  Maximum length is 64 characters.

location: 1st floor, south wall

# Contact is the name of the person who administers or services the
# peripheral and may include how to contact this person.  It is
# limited to 64 characters.  This is the value used by the interface
# for the MIB-II sysContact object.  The default contact is undefined.
# Only printable ASCII characters are allowed.  Maximum length is 64
# characters.

contact: Phil, ext 1234

# The host access list contains the list of hosts or networks of
# hosts that are allowed to connect to the peripheral.  The format
# is "allow: netnum [mask]", where netnum is a network number or a
# host IP address.  Mask is an address mask of bits to apply to the
# network number and connecting host's IP address to verify access
# to the peripheral.  The mask usually matches the network or subnet
# mask, but this is not required.  If netnum is a host IP address,
# the mask 255.255.255.255 can be omitted.  Up to ten access list
# entries are permitted.

# to allow all of network 10 to access the peripheral:
allow: 10.0.0.0  255.0.0.0

# to allow a single host without specifying the mask:
allow: 15.1.2.3

# Idle timeout is the time (in seconds) after which an idle
# print data connection is closed.  A value of zero disables
# the timeout mechanism.  The default timeout is 90 seconds.

idle-timeout: 120

# A community name is a password that allows SNMP access to MIB
# values on the network peripheral.
# Community names are not highly secure;
# they are not encrypted across the network.  The get community name
# determines which SNMP GetRequests are responded to.  By default,
# the network peripheral responds to all GetRequests.  The get
# community name is limited to 32 characters.

#
# For hpnpstat and hpnpadmin, the community name can be stored in
# /usr/lib/hpnp/hpnpsnmp.

get-community-name: blue

# The set community name is similar to the get community name.  The
# set community name determines which SNMP SetRequests are responded
# to.  In addition, SetRequests are only honored if the sending host
# is on the host access list.  By default, the network peripheral
# does not respond to any SetRequests.  The set community name is
# limited to 32 characters.
#
# The set community name can come from /usr/lib/hpnp/hpnpsnmp if it
# is the same as the get community name.  We recommend that the set
# community name be different from the get community name though.

set-community-name: yellow

# SNMP traps are asynchronous notifications of some event
# that has occurred.
# SNMP traps are useful only with network management software.
# Traps are sent to specific hosts and include a trap community
# name.  Up to four hosts can be sent SNMP traps.
# The trap community name is limited to
# 32 characters.  The default name is public.

trap-community-name: red

# The SNMP trap destination list specifies systems to which SNMP
# traps are sent.  Up to four IP addresses are allowed.  If no
# trap destinations are listed, traps are not sent.

trap-dest: 15.1.2.3
trap-dest: 15.2.3.4

# The SNMP authentication trap parameter enables or disables the
# sending of SNMP authentication traps.  Authentication traps indicate
# that an SNMP request was received and the community name check
# failed.  By default, the parameter is off.

authentication-trap: on

# The syslog-facility parameter sets the source facility identifier
# that the card uses when issuing syslog messages.  Other facilities,
# for example, include the kernel (LOG_KERN), the mail system
# (LOG_MAIL), and the spooling system (LOG_LPR).  The card only allows
# its syslog facility to be configured to one of the local user values
# (LOG_LOCAL0 through LOG_LOCAL7).  The selectible option strings,
# local0 through local7 (configured to LOG_LOCAL0 through LOG_LOCAL7,
# respectively) are case insensitive.  The default syslog-facility
# for the card is LOG_LPR.

syslog-facility: local2

# This parameter allows the card to treat hosts on other subnets as
# if the hosts were on the card's subnet.  This parameter determines
# the TCP Maximum Segment Size (MSS) advertised by the card to hosts
# on other subnets and affects the card's initial receive-window
# size.  The card will use a TCP MSS of 1460 bytes for local hosts,
# and 536 bytes for a non-local host.  The default is off, that is,
# the card will use the maximum packet sizes only on the card's
# configured subnet.
#
# The configuration utility does not allow access to this parameter.
# If you want to configure it, you must manually edit the NPI
# configuration file and add it to the bottom of the entry for the
# network peripheral.

subnets-local: on

# This parameter affects how the card handles TCP connection requests
# from the host.  By default, the JetDirect MPS card will accept a
# TCP connection even if the peripheral is off-line.  If this parameter
# is set to "on", then the card will only accept a TCP connection
# when the peripheral is on-line.

old-idle-mode: off